Get a quote

Free tool

Emissivity table and reading correction

An infrared thermometer set to 0.95 reads matt, painted and organic surfaces well and shiny metal badly. Look up your surface below, then correct a reading you have already taken.

Emissivity table and correctionCorrect a reading taken at the wrong emissivity
Updates
AS YOU TYPE
Corrected surface temperature
-
The reading was off by
-
How much to trust it
-

A broadband (Stefan-Boltzmann) estimate. Thermometers working at 8 to 14 µm differ, especially on hot metal, so treat it as a guide and confirm with tape, paint or a contact probe.

Look up the typical emissivity of the surface you are measuring, and correct a reading taken at the wrong setting, with the room temperature that the surface reflects taken into account.

What emissivity is

Every surface gives off infrared in proportion to its temperature, but not equally well. Emissivity (ε) is how well, on a scale from 0 to 1: a perfect emitter, a blackbody, is 1. Matt, dark and organic surfaces sit around 0.90 to 0.98, which is why most thermometers come set at 0.95. Shiny metals sit at 0.02 to 0.2: they give off little infrared of their own and reflect the room around them like a mirror, so a gun set at 0.95 reads them well below their true temperature and is easily fooled by your own body heat.

Emissivity table

SurfaceTypical εNote
Human skin0.98Why forehead thermometers work
Water0.95 to 0.96
Ice0.96 to 0.98
Snow0.80 to 0.90Some tables give up to 0.98
Most food: meat, vegetables, dough0.95 to 0.97Surface only; use a probe for the core
Wood, unfinished0.90 to 0.95
Paper and cardboard0.90 to 0.95
Cloth and textiles0.90 to 0.95
Rubber0.90 to 0.95
Plastics, opaque0.85 to 0.95Thin film may be see-through
Paint, most colours (not metallic)0.90 to 0.95
Matt black paint or electrical tape0.95 to 0.97Use as a reference patch
Concrete0.92 to 0.97
Brick, rough0.90 to 0.93
Asphalt0.93 to 0.97
Tar0.79 to 0.84
Plaster and drywall0.85 to 0.95
Glazed ceramic tiles0.90 to 0.94
Glass, plain sheet0.85 to 0.94Reads the glass, not what is behind it
Soil, dry0.90 to 0.95
Sand0.90
Graphite0.70 to 0.98Filed or powdered graphite sits near the top
Aluminium, polished0.02 to 0.10Reflects the room: do not trust a reading
Aluminium, rough0.07 to 0.30
Aluminium, oxidised0.20 to 0.40
Aluminium, anodised0.60 to 0.90
Stainless steel, polished0.10 to 0.20
Steel, galvanised, new0.20 to 0.30
Steel, oxidised or rusted0.60 to 0.90Heavy rust is near the top
Cast iron, oxidised0.60 to 0.90
Copper, polished0.02 to 0.05Busbars: use tape or a camera with care
Copper, oxidised0.60 to 0.80
Brass, polished0.03 to 0.10
Gold and silver, polished0.02 to 0.04

Typical values at 8 to 14 µm, the band of most handheld infrared thermometers and thermal cameras, as published in makers' tables. The finish, oxidation, temperature and viewing angle all change the real value; pyrometers working at short wavelengths use their own tables. See pyrometers.

Three ways to get a good reading on a tricky surface

  1. The tape trick: stick a patch of matt black electrical tape or a dab of matt paint on the surface, wait for it to reach the same temperature, and read the patch at 0.95. Only on a surface that is safe to touch and dead.
  2. Set ε by comparison: measure a spot with a contact probe or thermocouple, then adjust the emissivity on the infrared thermometer until it agrees. Note the value for that material.
  3. Read an oxidised or painted part nearby instead of the bright metal, or use a contact probe. A thermometer with adjustable emissivity and a Type K input does both; see temperature guns.

Frequently asked questions

What emissivity should I set on my infrared thermometer?
0.95 suits most non-metals: food, skin, wood, paper, rubber, paint, concrete and plastics. For metals, look the surface up in the table, or use tape or a probe, because polished metal can be 0.1 or lower.
Why does my temperature gun read too low on stainless steel?
Polished stainless has an emissivity of about 0.1 to 0.2, so most of what reaches the thermometer is the reflected room, not the steel. Lower the emissivity setting if your model allows it, or read a patch of tape.
Does emissivity matter for thermal cameras?
Yes, the same way. Cameras also let you enter the reflected temperature, which matters most on low-emissivity surfaces. In electrical thermography, shiny busbars and connections are the usual trap.
My thermometer has fixed emissivity. What can I do?
Most fixed models are set to 0.95. Read only matt and non-metal surfaces, or use the tape trick. If you often measure metal, ask for a model with adjustable emissivity on your quote request.

Other free tools

Free quote request, no obligation

Request quotes for temperature guns

Describe it the way a technician would: how far away you stand and how big the target is, or the camera and the distance, or simply how many. The planner draws the measuring cone or the camera's view as you type. Suppliers and service companies in your area quote you directly.

Measurement sheet and quote requestTemperature Guns
Req
18119
Date
2026-11-20
Cost
FREE

1The job

2The spot and the distance (optional, it helps the quote)

MEASURING CONEROUGH, NOT TO SCALE

-
-
-
-
-
-
Estimate
-

Plain geometry for the request, not a measurement.

3Where you are now

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: instruments, probes, certificates or services.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers and service companies. See our privacy policy.

Get a free quote