A thermometer that reads two degrees out can pass bad food, spoil a batch or fail an audit, and you would not know from looking at it. Thermometer calibration compares your instrument with a reference of known accuracy and records the difference, and the uncertainty of that comparison, on a certificate. Labs calibrate probe thermometers, infrared guns, thermal cameras, data loggers, thermocouples and PT100 sensors, in their lab or on your site. This page explains accreditation, methods, test points and intervals. Send one request and independent calibration labs that serve your area quote you directly.
What a calibration certificate tells you
A proper certificate lists each test point, what the reference read, what your instrument read, the error and the measurement uncertainty. It names the reference equipment and shows that it is itself traceable, through a chain of calibrations, to the national measurement standards kept by NMISA, the National Metrology Institute of South Africa. If the lab adjusted the instrument, a good certificate shows the readings before and after. A sticker with a date and a pass mark is not a certificate. Read the errors against your own tolerance: a probe that is 0.8 °C out may be fine for a braai and not fine for a pharmaceutical cold room.
Accredited or not, and why auditors care
ISO/IEC 17025 is the international standard for calibration and testing labs. In South Africa, SANAS (the South African National Accreditation System) assesses labs against it and publishes a scope of accreditation for each one, showing which instruments, ranges and uncertainties it covers. Auditors for ISO 9001, food safety schemes, pharmaceutical good practice and mining usually ask for accredited certificates. A non-accredited calibration can still be useful for internal checks, but ask whether your auditor will accept it, and check that the lab's scope covers your instrument and range, not just temperature in general.
How different instruments are calibrated
Contact probes, thermocouples and PT100 sensors go into a stirred liquid bath or a dry block calibrator next to a reference probe. Infrared thermometers and thermal cameras are aimed at a blackbody source, a target of known emissivity held at a set temperature. Data loggers are usually placed in a chamber or bath and their records compared with the reference. The test points should match how you use the instrument: for a kitchen probe, perhaps 0, 75 and 100 °C; for a vaccine fridge logger, points around 2 to 8 °C.
How often, and in the lab or on site
Many quality systems set a yearly interval, but the interval is yours to set, based on how hard the instrument is used, how stable it has been and what your auditor expects. Between calibrations, simple checks catch problems early: a probe in iced water should read close to 0 °C. Sending instruments to a lab often takes about a week, so plan spares. On site calibration suits fixed sensors, ovens and plants that cannot release their instruments, and saves the courier risk. Ask the lab which methods it can bring to you.
What to put in your request
- Each instrument: type, range and serial number
- The test points you need, for example 0, 75 and 100 °C
- Whether you need SANAS accredited certificates
- Lab or on site, and how many instruments on site
- When the audit is or when the old certificates expire
Thermometer Calibration for industry, food, health, labs and homes
- Factories, mines and plants: process probes, thermocouples and pyrometers calibrated on site during a shutdown
- Kitchens, butcheries and food factories: kitchen and factory probe thermometers calibrated before the food safety audit
- Hospitals, clinics and pharmacies: vaccine fridge loggers and clinical thermometers checked against a reference
- Electricians, HVAC and refrigeration technicians: temperature guns and multimeter probes checked so readings hold up on the job
- Labs, schools and universities: reference thermometers and PT100 probes calibrated with accredited certificates
- Cold stores and distributors: cold room loggers and alarm sensors calibrated around 2 to 8 °C and -18 °C
- Farms, poultry houses and packhouses: incubator, dairy and poultry house thermometers and hygrometers checked yearly
- Households and families: a good cooking or pool thermometer checked when its readings seem off
- Property managers, inspectors and security: building management sensors and HVAC probes calibrated for maintenance records
Frequently asked questions
Can I check my own thermometer between calibrations?
What happens if my instrument fails?
How do I know a lab is really accredited?
Do you calibrate instruments yourselves?
Thermometer Calibration by province and city
- Johannesburg
- Pretoria
- Centurion
- Midrand
- Sandton
- Randburg
- Roodepoort
- Krugersdorp
- Randfontein
- Germiston
- Boksburg
- Benoni
- Kempton Park
- Alberton
- Vanderbijlpark
- Vereeniging
- Durban
- Pinetown
- Pietermaritzburg
- Richards Bay
- Newcastle
- Ladysmith
- Gqeberha (Port Elizabeth)
- East London
- Kariega (Uitenhage)
- Mthatha
- Cape Town
- Bellville
- Paarl
- Stellenbosch
- George
- Worcester
- eMalahleni (Witbank)
- Middelburg
- Secunda
- Mbombela (Nelspruit)
- Rustenburg
- Brits
- Klerksdorp
- Potchefstroom
- Mahikeng
- Polokwane
- Tzaneen
- Kimberley
- Upington
- Bloemfontein
- Welkom
- Sasolburg
