Get a quote

Free tool

Boiling point at altitude and the thermometer check

Water only boils at 100 °C at sea level. On the Highveld it boils about 5 to 6 °C lower, which matters when you check a probe in boiling water. Pick your town or type the altitude, then enter what your thermometer reads.

Boiling point and thermometer checkBoiling point where you are, then your thermometer's error
Updates
AS YOU TYPE

2Your thermometer's readings Leave blank to skip

Air pressure
-
Water boils at
-
Ice point
-
Error in ice
-
Error in boiling water
-
Verdict
-

Standard atmosphere and the Antoine equation for water. Weather moves the boiling point by a few tenths of a degree; a barometer reading of the actual (station) pressure beats the altitude. Weather reports give sea-level pressure, which is no use here.

Work out what water boils at for your town or altitude, then check a probe thermometer against the ice point and the local boiling point and see how far off it reads.

Why water boils below 100 °C inland

Water boils when its vapour pressure matches the air pressure around it. Air pressure falls as you climb, so water boils cooler: roughly 1 °C lower for every 300 m. In Johannesburg, at about 1,750 m, a pot boils at about 94 °C. A probe that reads 100 °C there is reading about 6 °C high, not perfectly. The same thing makes food take longer to cook on the Highveld and pressure cookers useful.

TownAltitude, aboutAir pressureWater boils at
Sea level: Cape Town, Durban, Gqeberha, East London0 m101.3 kPa100.0 °C
Mbombela660 m93.6 kPa97.8 °C
Pietermaritzburg670 m93.5 kPa97.8 °C
Upington840 m91.6 kPa97.2 °C
Rustenburg1,170 m88.0 kPa96.1 °C
Kimberley1,200 m87.7 kPa96.0 °C
Polokwane1,310 m86.5 kPa95.7 °C
Pretoria1,340 m86.2 kPa95.6 °C
Bloemfontein1,400 m85.6 kPa95.4 °C
Johannesburg1,750 m82.0 kPa94.2 °C

How to do the ice point check

  1. Fill a glass or flask to the top with crushed ice, ideally from clean water, then add just enough cold water to fill the gaps. It should be mostly ice, not water with a few cubes floating.
  2. Stir and leave it for a couple of minutes.
  3. Put the probe in the middle, at least 5 cm deep, without touching the sides or bottom.
  4. Wait until the reading stops changing, then read it. It should show 0 °C.

The ice point is the better of the two checks: it does not change with altitude or weather, and it sits near the temperatures that matter for fridges and cold rooms.

How to do the boiling point check

Bring clean water to a rolling boil in a deep pot. Hold the probe in the water, away from the bottom and sides, and wait for the reading to settle. Compare it with the boiling point for your altitude, not with 100 °C. Steam and splashes can burn, so use a long probe and keep hands clear. Infrared thermometers cannot be checked this way: they read the water's surface, which is affected by steam and emissivity. They need a blackbody source, which a calibration lab has.

A check, not a calibration

These checks catch a probe that has drifted or been dropped, which is why many food safety plans ask for them weekly or before a shift. They are not a calibration: there is no reference thermometer, no uncertainty and no certificate. If an auditor, insurer or quality system relies on the readings, have them calibrated by a lab with traceability to national standards, and keep doing the ice check in between. If a thermometer fails, many can be adjusted; others need repair or replacing.

Frequently asked questions

What temperature does water boil at in Johannesburg?
About 94 °C, because the city sits at around 1,750 m where the air pressure is about 82 kPa instead of 101 kPa. Pretoria and Bloemfontein are a little warmer, at about 95 °C.
How accurate should my food thermometer be?
Many food safety plans accept a probe within about ±1 °C at the ice point, but check your own plan or auditor. If yours is further out, adjust it if the model allows, or replace it. See food thermometers.
Does salt or sugar in the water change the result?
Yes. Dissolved salt or sugar raises the boiling point and lowers the freezing point, so use clean tap or bottled water for both checks.
Can I check an infrared thermometer in iced water?
Only roughly. Water has an emissivity of about 0.95, so a gun set to 0.95 should read close to 0 °C on the surface of a well stirred ice bath, but frost, condensation and the distance to spot ratio all get in the way. For a real check, use a blackbody calibrator.

Other free tools

Free quote request, no obligation

Request quotes for thermometer calibration

Describe it the way a technician would: how far away you stand and how big the target is, or the camera and the distance, or simply how many. The planner draws the measuring cone or the camera's view as you type. Suppliers and service companies in your area quote you directly.

Measurement sheet and quote requestThermometer Calibration
Req
64380
Date
2026-11-20
Cost
FREE

1The job

2How many (optional, it helps the quote)

YOUR REQUESTROUGH, NOT TO SCALE

-
-
-
-
-
-
Estimate
-

Plain geometry for the request, not a measurement.

3Where you are now

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: instruments, probes, certificates or services.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers and service companies. See our privacy policy.

Get a free quote